Advanced Machines Make Quality FRP Pipe Liners

Liner making machine, as its name implies, is specially designed for fabricating the liner layers of fiberglass reinforced plastic (FRP) pipes. It has auto resin spraying device and Taida PLC numerical control device. Thus, resin can be sprayed in accurate quantity to prevent waste phenomenon. Meanwhile, the film, mat and grid fabric are winded automatically to the mandrel by a trolley moving horizontally along the mandrel.

Equipped with tension brackets, our liner making machine allows for smooth & precise lap joints without any artificial nonconformity and inaccuracy. Meanwhile, it adopts frequency conversion linkage control system between the mandrel and moving trolley, that is to say, the trolley can move in different speeds accompanied with the mandrel. In addition, the trolley moves smoothly by gear wheel and it has monitor platform to convenient control & operation.

An orange liner making machine for producing FRP pipe lines.
Liner making machine for liner manufacturing of FRP pipes.
A red liner making machine equipped with Taida PLC device allows for accurate control.
Liner making machine is equipped with Taida PLC device for accurate control.

Composition:

  • Liner making rails.
  • Liner making driving headstock.
  • Tail stock.
  • Liner making trolley.
  • Taida PLC numerical control device
  • Resin delivery system.
  • Spray heads.
  • Pneumatic pressing roll.
  • Polyester film winding stand, etc.

Details:

  • Pipe diameter of liner making: up to 2600mm.
  • Workable length: up to 12m.
  • Rotation speed: 3r/min to 30r/min.
  • Speed of trolley: 9m/min.
  • Machine height: 1600mm.
  • Covering areas: 38m × 19m × 2.8m (L × W × H).
  • Load capacity: 7.5kW.
  • Custom designs and sizes are also welcomed.

For liner making of large tanks, we offer two kinds of machines: cantilever beam liner making machine and double output beam liner making machine.

Cantilever Beam Liner Making Machine

One cantilever beam liner making machine is in the warehouse and its beam is inside the tank mould.
Cantilever beam liner making machine could manufacture more beautiful liner than traditional rolled plate.

Cantilever Beam tank liner making machine is one structure, which is designed with cantilever beam style. It is matched with tank mold to make the liner of tank. The liner is more beautiful than made by the way of traditional rolled plate. This device improves work efficiency as well as decreasing labor strength and reducing production cost.

Device configuration:
Main component: body, power system, mold support saddle, electric control system.

Product range

  • DN1000-DN1600, maximum length 6500 mm FRP tank liner making.
  • DN1800-DN2200, maximum length 8500 mm FRP tank liner making.
  • DN2400-DN3000, maximum length 12000 mm FRP tank liner making.
  • DN3000-DN4000, maximum length 12000 mm FRP tank liner making.
  • DN4500, maximum length 13500 mm FRP tank liner making.

Main technical parameter

  1. The maximum rotating speed of main shaft: 30 rpm.
  2. The maximum total capacity: 11±3 kW.
  3. The maximum occupied areas: 5500 mm × 15000 mm.

Double output beam liner making machine

There is one double output beam liner making machine in the warehouse and its two beams are inside two pipe moulds.
The double output beam liner making improves working efficiency by two beams making liner at the same time.

Double output beam tank liner making device upgrades to improve based on cantilever beam, which plays a maximum use efficiency to increase the liner diameter range, then decrease the occupied areas.

Device configuration
Main component: body, power system, mold support saddle, electric control system.

Production range

  • DN1000-DN3000 double output beam
    Small beam applied diameter range: DN1000-DN2000, maximum length 8500 mm FRP tank liner making.
    Big beam applied diameter range: DN2200-DN3000, maximum length 12000 mm FRP tank liner making.
  • DN1800-DN4000 double output beam
    Small beam applied diameter range: DN1800-DN2800, maximum length 12000 mm FRP tank liner making.
    Big beam applied diameter range: DN3000-DN4000, maximum length 12000 mm FRP tank liner making.

Main technical parameter

  • The maximum rotating speed of main shaft: 30 rpm.
  • The maximum total capacity: 11±3 kW.
  • The maximum occupied areas: 4500 mm × 26000 mm.

Inquiry for Our Product

Hengshui Fangchen FRP Equipment Technology Co., Ltd.
E-mail: info@frpmachine.com

When you contact us, please provide your detail requirements. That will help us give you a valid quotation.

Full Name *
Country Code * + Phone Number *
Your Website
Message *